User Manual - JE-Plus Grinder
Do not wash or soak this product for cleaning
目次
User Instructions
Adjusting the grind setting
Turn the adjustment nut/adjustment dial clockwise to make the grinds finer and vice versa.
- Turn the adjustment dial clockwise to the tightest. The number (#) marked at the dot is the starting point/zero point.
NOTE: the number (#) might not be 0; however, it is attainable if you like to calibrate to the #0. Check out here or the tutorial below. - Turn the adjustment dial counter-clockwise from the zero point to the grind setting you like.
- There are 10 numbers/40 clicks in a single rotation; every rotation moves the burr by 0.5mm.
- Grinds remaining in the grinder might make the zero points different.
- Kindly refer to the grind setting tutorial post for several brewing methods.
Coffee Grinding
- Put the coffee bean into the hopper after removing the handle. The maximum capacity is around 35~40g.
- Grind coffee beans clockwise with the handle attached.
Disassembly
- Loosen the adjustment dial counter-clockwise to remove it.
- Remove the adjustment dial. Loosen the knurled thumb nut counter-clockwise while pushing the burr from the bottom. Take out the top bearing cover, the top bearing and the sliding column/screw column.
- Take out the shaft, burr, lower bearing cover および spring.
- Turn the burr ring unit and the upper ring cap clockwise to remove them from the grinder.
- Clean each of the parts with a brush and an air blower.
Reassembly
- Turn the burr ring unit and the upper ring cap counter-clockwise to the tightest position. Be sure to do not overtighten and stop when you feel resistance.
- Put the components back in the right sequence: lower bearing cap (the raised edge side facing upward), spring, shaft および burr.
- There is a dot at the back of the sliding column. Place the sliding column (which connects the dot at the sliding column to the dot at the adjustment dial) inside the hopper.
- Put the components back in the right sequence while pressing the burr: sliding column, upper bearing, upper bearing cap (the concave edge of the cap facing upward).
- Turn the knurled thumb nut clockwise while pushing the burr.
- Free your hand from pressing the burr, tighten the adjustment dial clockwise and stop when you feel resistance.
Warning
Do not attempt to disassemble or remove the following components any further:
- You would need to either loosing or tightening the knurled thumb nut or the adjustment dial to calibrate the grinder.
- The numbers on the dial are designed to count how many steps you’ve turned and therefore the starting point is not necessary to be at #0.
- It is common for the starting point of the adjustment dial to be around two or more clicks away due to the strength of tightening the knurled thumb nut.
Instructions
- The grinder is well-calibrated if the dot is at #0 when the adjustment dial is in its tightest position.
- When the dot points to #1 instead of #0 at the tightest, please simply remove the adjustment dial (by twisting it counterclockwise).
Adjust the knurled thumb nut counter-clockwise with 1 click. - Screw back the adjustment dial and the starting point should be at #0 (±2 clicks).
- It is the same as step 2, simply remove the adjustment dial (by twisting it counterclockwise).
Except for the dot points now is at #2, so you need to adjust the knurled thumb nut counter-clockwise with 2 clicks. - Screw back the adjustment dial and the starting point should be at #0 (±2 clicks).
Warning: The handle will not be covered by warranty if any part is taken apart.
How to fold?
- Hold the crank part near the wooden knob and push it in.
- Turn the handle clockwise all the way to fold.
How to unfold?
- Hold the crank part near the wooden knob and push it in.
- Turn the handle counter-clockwise all the way to unfold.
Precautions
- Do not clean and wash the grinder with water.
- Do not wipe your grinder with solvents other than water and alcohol.
- Keep it in a dry environment in order to extend its lifetime.
- Follow the instructions of re-assembly, ensure to place the components into the correct positions.
- Keep the grinder away from children for safety concerns.
Read More >>
完璧なドリップコーヒーの究極ガイド！
Pour-over coffee is a manual brewing method that allows for a clean, flavorful cup, favored by enthusiasts for its control. The guide outlines necessary equipment, step-by-step instructions, and tips for optimal brewing, emphasizing the importance of water temperature, coffee grind consistency, and experimentation to enhance flavor.
5月 21, 2024
コメントはまだありません
コーヒー抽出の初心者ガイド
This guide introduces beginners to the art of coffee brewing, emphasizing the importance of understanding coffee beans, roast types, and essential equipment. It outlines the brewing process and popular methods, offering tips to enhance flavor, such as measuring ratios, grind consistency, and equipment maintenance. Ultimately, it encourages experimentation for optimal home-brewed coffee.
5月 21, 2024
コメントはまだありません
コメントを投稿するにはログインしてください。