fbpx

User Manual - JE-Plus Grinder

C-JE-Plus
C-2-JE-Plus

⚠ Do not wash or soak this product for cleaning

Table of Contents

User Instructions

Adjust the dial clockwise for finer grinds. Adjust the dial counter-clockwise for coarser grinds.

Adjusting the grind setting

Turn the adjustment nut/adjustment dial clockwise to make the grinds finer and vice versa.

  1. Turn the adjustment dial clockwise to the tightest. The number (#) marked at the dot is the starting point/zero point.
    NOTE: the number (#) might not be 0; however, it is attainable if you like to calibrate to the #0. Check out here or the tutorial below.
  2. Turn the adjustment dial counter-clockwise from the zero point to the grind setting you like.
  3. There are 10 numbers/40 clicks in a single rotation; every rotation moves the burr by 0.5mm.
  4. Grinds remaining in the grinder might make the zero points different.
  5. Kindly refer to the grind setting tutorial post for several brewing methods.

Coffee Grinding

  1. Put the coffee bean into the hopper after removing the handle. The maximum capacity is around 35~40g.
  2. Grind coffee beans clockwise with the handle attached.
JE-Plus

Diassembly

JX-Pro manual coffee grinder
  • Loosen the adjustment dial counter-clockwise to remove it.
JE-Plus Grinder
  • Remove the adjustment dial. Loosen the knurled thumb nut counter-clockwise while pushing the burr from the bottom. Take out the top bearing cover, the top bearing and the sliding column/screw column.
JE-Plus Grinder
  • Take out the shaftburrlower bearing cover and spring.
JE-Plus Grinder
  • Turn the burr ring unit and the upper ring cap clockwise to remove them from the grinder.
  • Clean each of the parts with a brush and an air blower.

Reassembly

JE-Plus Grinder
  • Turn the burr ring unit and the upper ring cap counter-clockwise to the tightest position. Be sure to do not overtighten and stop when you feel resistance.
JE-Plus Grinder
  • Put the components back in the right sequence: lower bearing cap (the raised edge side facing upward), spring, shaft and burr.
JE-Plus Grinder
  • There is a dot at the back of the sliding column. Place the sliding column (which connects the dot at the sliding column to the dot at the adjustment dial) inside the hopper.
JE-Plus Grinder
  • Put the components back in the right sequence while pressing the burr: sliding columnupper bearingupper bearing cap (the concave edge of the cap facing upward).
JE-Plus Grinder
  • Turn the knurled thumb nut clockwise while pushing the burr.
  • Free your hand from pressing the burr, tighten the adjustment dial clockwise and stop when you feel resistance.

Warning

Do not attempt to disassemble or remove the following components any further:
JE-Plus Grinder manual coffee grinder
The central shaft and the burr
JE-Plus Grinder manual coffee grinder
The burr ring unit and outer burr
JE-Plus Grinder manual coffee grinder
The bearings attached to the upper shaft hopper
  • You would need to either loosing or tightening the knurled thumb nut or the adjustment dial to calibrate the grinder. 
  • The numbers on the dial are designed to count how many steps you’ve turned and therefore the starting point is not necessary to be at #0.
  • It is common for the starting point of the adjustment dial to be around two or more clicks away due to the strength of tightening the knurled thumb nut.

Instructions

JX-Pro grinder
  • The grinder is well-calibrated if the dot is at #0 when the adjustment dial is in its tightest position.
JX-Pro grinder
  • When the dot points to #1 instead of #0 at the tightest, please simply remove the adjustment dial (by twisting it counterclockwise).
    Adjust the knurled thumb nut counter-clockwise with 1 click.
  • Screw back the adjustment dial and the starting point should be at #0 (±2 clicks).
JX-Pro grinder
  • It is the same as step 2, simply remove the adjustment dial (by twisting it counterclockwise).
    Except for the dot points now is at #2, so you need to adjust the knurled thumb nut counter-clockwise with 2 clicks.
  • Screw back the adjustment dial and the starting point should be at #0 (±2 clicks).

Warning: The handle will not be covered by warranty if any part is taken apart.

How to fold?

1Zpresso K-Ultra grinder
  • Hold the crank part near the wooden knob and push it in.
1Zpresso K-Ultra grinder
  • Turn the handle clockwise all the way to fold.

How to unfold?

1Zpresso K-Ultra grinder
  • Hold the crank part near the wooden knob and push it in.
1Zpresso K-Ultra grinder
  • Turn the handle counter-clockwise all the way to unfold.

Precautions

  • Do not clean and wash the grinder with water.
  • Do not wipe your grinder with solvents other than water and alcohol.
  • Keep it in a dry environment in order to extend its lifetime.
  • Follow the instructions of re-assembly, ensure to place the components into the correct positions.
  • Keep the grinder away from children for safety concerns.
Shopping Cart

Refunds

(For example: JX $129 + Shipping $10 = Total $139)

If YouYou’ll Receive
Cancel before an item is shippedfull refund (item’s price + shipping)
= $139
Return an item in original condition within 7 calendar days from the date you received it100% of the item’s price
= $129
Return an item in original condition over 7 calendar days from the date you received it80% of the item’s price
= 129*0.8 = $103.2

*Any customs duty or relevant charges incurred will be deducted from the refund. (The table above does not include additional charges.)

 

*A refund request over 7 calendar days from the date you received an item will be refunded partially (80% of the item’s price) and might be denied since the item has been used.