User Manual - K-series (K-Pro / K-Plus / K-Max / ZP6 Special) Grinder
Do not wash or soak this product for cleaning
目次
User Instructions
Adjusting the Grind Setting
- Turn the adjustment dial ring to set your preferred grind size. The dial pointer indicates the setting—higher numbers correspond to coarser grinds. Avoid overtightening the dial to prevent the grinder from getting stuck.
- The dial has 90 clicks per full rotation and can go above one rotation, with each click moving the burr by 0.022mm (22 microns).
- After reassembling the grinder, calibrate the adjustment dial ring according to the guide below.
- Check the grind setting tutorial post for recommended settings based on different brewing methods.
Pour beans into the hopper and turn the handle clockwise to grind.
Coffee Grinding
- Remove the handle and add coffee beans to the hopper.
- K-Pro grinder: Maximum capacity is approximately 30–35g.
- K-Plus grinder: Maximum capacity is approximately 35–40g.
- Reattach the handle and grind the coffee beans by turning it clockwise.
Disassembly
( Demonstrating with the K-Plus grinder )
- Turn the adjustment dial ring clockwise to coarser grind settings as the burrs open up.
- Loosen the knurled thumb nut by turning it counterclockwise while pushing the burr. Then, remove the upper bearing cap および upper bearing from the top.
- Remove the shaft, inner burr, lower bearing coverと spring.
- Detach the burr ring unit and the entire adjustment dial unit by turning it clockwise.
- Clean all parts using a brush and an air blower.
Assembly
- Turn the entire adjustment dial unit counterclockwise to its tightest position.
- Rotate the adjustment dial ring clockwise to set a coarser grind setting.
- Turn the burr ring unit counterclockwise to its tightest position.
- Insert the spring followed by the bearing cap (raised edge facing upward) onto the shaft, then place the shaft back into the grinder.
- While pressing the burr, reinstall the upper bearing および upper bearing cap (dotted side facing upward). Ensure the bearing cap is placed correctly.
- Turn the knurled thumb nut clockwise while pushing the burr, stopping when you feel resistance.
- Set the adjustment dial ring to zero and check if the indicator aligns with #0.
- If misaligned, refer to the calibration guide below.
Warning: Do not further disassemble or remove the following parts:
- To calibrate the grinder, adjust the knurled thumb nut by either loosening or tightening it.
- The zero point is defined as the position where the handle begins to spin with resistance, not the absolute tightest position. Avoid overtightening the dial to prevent it from getting stuck.
- The zero point may be offset by two or more clicks due to the force applied when tightening the adjustment dial ring.
Instructions
- Find the Zero Point: Turn the adjustment dial ring counterclockwise until you feel resistance (the handle starts to spin with resistance), not the tightest position. This is the zero point.
- Verify Alignment: The grinder is calibrated if the dial pointer aligns with #0 when the adjustment dial ring is at its zero point.
- Adjust if Needed: If the dial pointer does not align with #0, follow the steps below to calibrate.
Read the following steps for calibration if you don’t get #0 for the zero setting.
If the Dial Pointer is to the Right of #0:
- Turn the adjustment dial ring clockwise to a coarser setting, increasing the gap inside.
- Loosen the knurled thumb nut slightly by turning it counterclockwise while pressing the burr from the bottom.
- Turn the adjustment dial ring counterclockwise back to the zero setting and check the dial pointer.
- Repeat as needed until properly calibrated.
If the Dial Pointer is to the Left of #0:
- Turn the adjustment dial ring clockwise to a coarser setting, increasing the gap inside.
- Tighten the knurled thumb nut slightly by turning it clockwise while pressing the burr from the bottom.
- Turn the adjustment dial ring counterclockwise back to the zero setting and check the dial pointer.
- Repeat as needed until properly calibrated.
Quick Calibration Method
Warning: The handle will not be covered by warranty if any part is taken apart.
How to fold?
- Hold the crank part near the wooden knob and push it in.
- Turn the handle clockwise all the way to fold.
How to unfold?
- Hold the crank part near the wooden knob and push it in.
- Turn the handle counter-clockwise all the way to unfold.
Precautions
- Do not wash or clean the grinder with water.
- Store the grinder in a dry place to maintain its longevity.
- Follow the disassembly and reassembly instructions carefully, ensuring all parts are in the correct order and position.
- Keep out of reach of young children. This is not a toy and should be handled with care.
コメントを投稿するにはログインしてください。